Barco PJWU-101B Uživatelský manuál stáhnout pdf (Strana 73)

PJWU-101B 17/10/2014

14.Lamp and Filter Maintenance

Use a screw driver to loosen the screws as shwon in the illustration.

Pull the lamp out.

Insert the new lamp in the direction shown in the illustration into the lamp assembly; tighten the two screws using a

screw diver and make sure the lamp is ﬁrmly secured to prevent the lamp from shaking or poor contact.

Replace the lamp cover and ﬁrmly secure the four screws on the lamp cover.

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 85 86

PJWU-101B 1
Barco nv Projection Division 2
1. SAFETY 1 4
2. GENERAL 5 4
3. PHYSICAL INSTALLATION 12 4
5. GETTING STARTED 29 5
6. ADVANCED OSD MENU 35 5
7. INPUT 37 5
8. IMAGE 40 6
9. LAYOUT 48 6
10. LAMP 51 6
11. ALIGNMENT 54 7
12. CONTROL 58 7
13. SERVICE 62 7
14. MAINTENANCE 64 8
1. SAFETY 9
Users deﬁnition 10
To prevent personal injury 10
To prevent ﬁre hazard 11
To prevent projector damage 11
On servicing 12
To prevent battery explosion 12
2. GENERAL 13
2.2 Unpacking the projector 14
2.3 Initial inspection 15
2.4 Projector conﬁgurations 16
Rear projection 17
Positioning the projector 17
On axis / off axis projection 17
Shift range 18
Ventilation inlet 19
Ventilation outlet 19
3. PHYSICAL INSTALLATION 20
Remote Control overview 21
IR LED'S 21
3.2 Lenses 22
Lens focus 23
Lens zoom 23
Lens Shift 24
Connect to Wall plug 25
3.Physical Installation 26
Angle adjustment 27
Necessary tools 28
How to mount 28
4.1 Projector front view 29
4.2 Projector Rear view 29
4.3 Input and Communication 30
3. 12V TRIGGER 31
4. IR EXT 31
4.4 Status lights of LED 32
HDMI connection 33
12V Trigger connection 33
Desktop 34
RGBs connection 35
IR INPUT connection 35
(YPbPr) 36
5. GETTING STARTED 37
5. Getting Started 38
5.3 Power on projector 39
5.4 Switching to standby 39
5.5 Power off projector 39
5.7 Source selection 40
5.8 Changing OSD language 41
6. ADVANCED OSD MENU 43
6.3 Advanced menu memory 44
7. INPUT 45
7.2 Input Selection 46
7.3 Input Conﬁguration 46
7.4 Input Locking 46
7.5 Auto Power Off 47
7.6 Auto Power ON 47
7.7 No Signal 47
7.8 Auto Image Adjust 47
8. IMAGE 48
8.2 Contrast 49
8.3 Brightness 49
8.4 Sharpness 50
8.5 Noise Reduction 50
8.6 Color Temperature 50
8.7 Input Balance 51
Adjusting the input balance 52
8.8 Aspect Ratio 53
8.9 Timings 54
8.10 Auto Image 55
9. LAYOUT 56
9.2 Zoom 57
9.3 Main Select 57
9.4 PIP Select 58
9.5 PIP Position 58
9.6 PIP 58
10. LAMP 59
10.2 Mode 60
10.3 Lamps 60
11. ALIGNMENT 62
11.3 Rear Projection 63
11.4 Ceiling Mode 64
11.5 Lens Control 64
11.6 Keystone 64
11.7 Dynamic Contrast 64
11.8 Gamma 65
11.9 Internal Patterns 65
11.10 Color Space 65
11.11 Lens To Midposition 65
12. CONTROL 66
12.2 Eco Network Power 67
12.3 Network 67
12.4 Menu Position 68
12.5 Start Up Logo 69
12.6 Start Up Chime 69
12.7 Trigger1 ~2 69
12.8 Auto Source 69
12.9 Language 69
13. SERVICE 70
13.3 Lamp Hour Reset 71
13.4 Blue Only 71
13.5 Factory Reset 71
14. MAINTENANCE 72
Necessary parts 74
Black side 75
White side 75
Lado negro 76
Lado blanco 76
14.4 Cleaning the lens 77
14.6 Simple troubleshooting 78
15. PROJECTOR SPECIFICATION 80
15.2 STANDARD SOURCE FILES 81
15.3 Dimension 82
16. ENVIRONMENTAL INFORMATION 83
本产品中包含的有毒有害物质/成分的名称和含量。 84
16.3 Production address 85

Komentáře k této Příručce

Žádné komentáře

Barco PJWU-101B Uživatelský manuál Strana 73

Komentáře k této Příručce

Související produkty a manuály pro Datové projektory Barco PJWU-101B